This standard is issued under the fixed designation A /A M; the 1 This specification is under the jurisdiction of ASTM Committee A ASTM A/AM: Standard Specification for Steel, Sheet and Strip, Heavy- Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural. Find the most up-to-date version of ASTM A at Engineering
|Published (Last):||27 September 2008|
|PDF File Size:||1.19 Mb|
|ePub File Size:||7.8 Mb|
|Price:||Free* [*Free Regsitration Required]|
No Tolerance Under 7 16 12 9 16? MatWeb is intended for personal, non-commercial use.
ASTM A635 Grade 1018
Note 1—The term weight is used when inch-pound units are the standard. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Retests and Disposition of Non-Conforming Material This specification covers the general requirements for hot-rolled, heavy-thickness, and high-strength low-alloy with improved formability sheet and strip coils.
These tolerances do not include crown, and, therefore, the tolerances given in Table A1. Rejection and Rehearing a365 Historical Version s – view previous versions of adtm.
Over Over Over Over Over Over Over Over Over Over Over Over Over Over 12 14 17 19 21 24 26 28 35 50 60 65 70 80 to to to to to to to to to to to to to 14, 17, 19, 21, 24, 26, 28, 35, 50, 60, 65, 70, 80, incl incl incl incl incl incl incl incl incl incl incl incl incl Tolerance Over Speci?
AK Steel ASTM A and A Hot Rolled Carbon Steel, Structural Steel (SS)
When different grades of strand-cast steel are sequentially cast, identi?
Specimen preparation and test methods are discussed. Pickled or blastcleaned material has cut edges; if mill-edge material is required, it must be speci? Size Limits, Coils Only.
For steels other than non-killed capped or rimmedproduct analysis may be made. This abstract is a brief summary of the referenced standard. This table does not apply to the uncropped ends of mill edge coils.
For strip over 8 in. Hot roll manufacturer de? Users requiring more precise data for scientific or engineering calculations can click on the property value to see the original value as well as raw conversions to equivalent units. Referenced Documents purchase separately The documents listed below ashm referenced within the subject standard but are not provided as part of the standard.
NOTE 2—Micrometers used for measurement of thickness shall be constructed with anvils and spindles having minimum diameters of 0. Click here to view all the property values for this datasheet as they were originally entered into MatWeb. NOTE 2—The term weight is used when inch-pound units are the standard. Data sheets for overmetals, plastics, ceramics, and composites. Cut Edge and 3? Notwithstanding the absence of a653 signature, the organization submitting the document is responsible for the content of the document.
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. B The tolerances provided in astk table are based on minimum thickness tolerance over, no tolerance under.
Cut Edge and 1-in. Link to Active This link will always route to the current Active version of the standard. Packaging and Package Marking These tolerances do not include crown, and, therefore, the tolerance given in Table A1.
Micrometers with pointed tips are not suitable for thickness measurements. Approved May 1, Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
All Widths A All Widths. The resampling shall be appropriate to the speci? Product analysis is appropriate on these types of steel only when misapplication is apparent, or for copper when copper steel is speci?
Within the text, the SI units are shown in brackets.
For nominal thickness, the tolerance is divided equally over and under. Dimensions and Tolerances 8. Current edition approved Sept.