CONTAX 139 MANUAL PDF

Repair and service information for the Contax camera. The Contax service manual gives a comprehensive list of possible causes of various symptoms and I suggest you refer to that if the cause of your problem. Contax Quartz 35mm SLR camera, Contax Q, Q. TTL metering system using a silicon photo diode, manual or aperture-priority exposure controls .

Author: Telabar Vugore
Country: Algeria
Language: English (Spanish)
Genre: Finance
Published (Last): 24 September 2017
Pages: 80
PDF File Size: 9.4 Mb
ePub File Size: 6.5 Mb
ISBN: 528-9-47524-582-1
Downloads: 36540
Price: Free* [*Free Regsitration Required]
Uploader: Tygozilkree

Also the spring contacts which are attached to the underside of the click plate. Details of the full differences can ocntax found here. Remove it again and apply a small amount of glue to each plastic rivet then refit again.

There is a plate either side of the lens mount that can be removed. To refit the memo holder, clean up the plastic rivets that will have pulled through the holes.

Shutter speeds indicated by 14 LEDs where flickering indicates the user comtax speed, and continuous illumination indicates the camera’s auto shutter speed. The above method can be used to remove and refit the mirror if this happens.

This is what it looks like with the mirror box in place.

The stop has a rubber maybe plastic piece around the end of it for the mirror to rest against and this can sometimes come off. Work your way around to lift all four corners.

In total there was something overunits made and conatx a handful of cameras with serial numbers abovehave been seen. Also make sure the shorter of the two curved slots in the plate is nearest the prism. But be aware, if looking for a high serial number unit, there’s evidence that some baseplates with high serial numbers on them were used as replacement parts so contx camera may not match the serial number.

These contact the front plate. And so my Contax quartz was consigned to the scrap heap.

TOP Related  PYQT4 TUTORIAL EPUB

With the screw out, the lever can be lifted off. As long as you use the very thin tape not the thicker foam type the focus should be correct.

I suggest not attempting this unless you are absolutley sure there is a problem. The page does get updated occasionally as I get to record and write up more things. They all should be cleaned. This page was last modified on 17 Decemberat Next remove the metal clip that retains the wires that go to the shutter and also acts as an anchor point for the spring that is attached to the exposure compensation lock lever.

Quartz-timed electronic self-timer with precise 10 sec delay. Yashica also manufactured the Yashica FX-D which was seen as a budget version of the with less features but, in fact, was largely a completely different camera. There were a few modifications made to the camera during the period it was manufactured.

Contax Q | Camerapedia | FANDOM powered by Wikia

Press the holder back into place making sure the rivets fit back through the holes and the holder is all the way in.

Electrical Contacts Electrical contacts are always a potential source of problems. Refer to the section on lifting the flexible PCB to find out how to do this.

Next remove the rewind knob. The original transfer switch was replaced around the same time as the magnet change and then changed again around serial numberLens Mount Trim With the top and bottom covers off, the trim around the lens mount can be removed.

Contax 139Q

To do so, the front covers need to be removed first. Although there is some evidence that the original switch could fail, it wasn’t a common problem and the changes made might have been done as much for a manufacturing reason as for reliability.

This makes sure it will re-engage when you fit the ISO dial after fitting the top cover assuming the contact carrier doesn’t move of course. The holder can be quite easily removed using a flat, blunt, tool I use the handle of a pair of tweezers. This allows for the mirror mechanism to be supported while the old mirror is removed which, otherwise, might cause damage to the mirror mechanism through excessive strain being put on it.

TOP Related  HIPOPLASIA CEREBELOSA PDF

Unscrew the collet using a wrench. Service and repair information for the Contax The Contax Quartz with a 35mm f2.

Remove the trim from around the remote release socket. Undo the camera back and insert the blade of a screwdriver, or something similar, into the fork on contsx bottom end of the rewind shaft. The ISO dial itself rarely needs dismantling and is easily reassembled if you do. Coupling for power contqx. Once the viewfinder surround is removed, unscrew the three screws holding the flexi in place.

I clean screens with liquid soap and water then remove all the water by spraying with IPA then blow drying the screen with an air duster. The cover needs to fit under the edge of the holder and the original covers were thinner so they could fit. Next remove the film advance lever. Mirror Stop and Focus Errors The mirror stop is located in the mirror box arrowed in picture and the maunal rests against it when in the down position.

Making sure the back is slightly wet makes a big difference here because you need to slide the cover into place.

NEVER try and clean the screen in 319. Clean the spring contact on the underside of the contact plate. Underneath is a PCB with several gold plated tracks. Removing this plate allows better access to the mirror damper flywheel which sometimes squeaks and needs lubricating.